we provide Verified Check Point 156-915.80 exam answers which are the best for clearing 156-915.80 test, and to get certified by Check Point Check Point Certified Security Expert Update - R80. The 156-915.80 Questions & Answers covers all the knowledge points of the real 156-915.80 exam. Crack your Check Point 156-915.80 Exam with latest dumps, guaranteed!
P.S. Verified 156-915.80 software are available on Google Drive, GET MORE: https://drive.google.com/open?id=1YYqgCO6ctCwcBVUFbQYMfHPbrQOvemUT
New Questions 1
John detected high load on sync interface. Which is most recommended solution?
A. For short connections like http service u2013 delay sync for 2 seconds
B. Add a second interface to handle sync traffic
C. For short connections like http service u2013 do not sync
D. For short connections like icmp service u2013 delay sync for 2 seconds
New Questions 2
How could you compare the Fingerprint shown to the Fingerprint on the server? Exhibit:
A. Run cpconfig, select the Certificate's Fingerprint option and view the fingerprint
B. Run cpconfig, select the GUI Clients option and view the fingerprint
C. Run cpconfig, select the Certificate Authority option and view the fingerprint
D. Run sysconfig, select the Server Fingerprint option and view the fingerprint
New Questions 3
You run cphaprob -a if. When you review the output, you find the word DOWN. What does DOWN mean?
A. The cluster link is down.
B. The physical interface is administratively set to DOWN.
C. The physical interface is down.
D. CCP pakets couldn't be sent to or didn't arrive from neighbor member.
New Questions 4
Access Role objects define users, machines, and network locations as:
A. Credentialed objects
B. Linked objects
C. One object
D. Separate objects
New Questions 5
Your expanding network currently includes ClusterXL running Multicast mode on two members, as shown in this topology:
You need to add interfaces: 10.10.10.1/24 on Member A, and 10.10.10.2/24 on Member B. The virtual IP address for these interfaces is 10.10.10.3/24. Both cluster gateways have a Quad card with an available eth3 interface. What is the correct procedure to add these interfaces?
A. 1. Disable "Cluster membership" from one Gateway via cpconfig.2. Configure the new interface via sysconfig from the "non-member" Gateway.3. Re-enable "Cluster membership" on the Gateway.4. Perform the same steps on the other Gateway.5. Update the topology in the cluster object.6. Install the Security Policy.
B. 1. Configure the new interface on both members using WebUI.2. Update the new topology in the cluster
object from SmartDashboard.3. Define virtual IP in the Dashboard4. Install the Security Policy.
C. 1. Use WebUI to configure the new interfaces on both member.2. Update the topology in the cluster object.3. Reboot both gateways.4. Install the Security Policy.
D. 1. Use the command ifconfig to configure and enable the new interface on both members.2. Update the topology in the cluster object for the cluster and both members.3. Install the Security Policy.4. Reboot the gateway.
New Questions 6
When restoring R80 using the command upgrade_import, which of the following items are NOT restored?
A. SIC Certificates
C. Route tables
D. Global properties
New Questions 7
VPN Tunnel Sharing can be configured with any of the options below, EXCEPT One:
C. IP range based
VPN Tunnel Sharing provides interoperability and scalability by controlling the number of VPN tunnels created between peer Security Gateways. There are three available settings:
One VPN tunnel per each pair of hosts One VPN tunnel per subnet pair
One VPN tunnel per Security Gateway pair
New Questions 8
Your organizationu2019s disaster recovery plan needs an update to the backup and restore section to reap the new distributed R80 installation benefits. Your plan must meet the following required and desired objectives:
Required Objective: The Security Policy repository must be backed up no less frequently than every 24 hours. Desired Objective: The R80 components that enforce the Security Policies should be backed up at least once a week.
Desired Objective: Back up R80 logs at least once a week. Your disaster recovery plan is as follows:
- Use the cron utility to run the command upgrade_export each night on the Security Management Servers.
- Configure the organization's routine back up software to back up the files created by the command upgrade_export.
- Configure the GAiA back up utility to back up the Security Gateways every Saturday night.
- Use the cron utility to run the command upgrade_export each Saturday night on the log servers.
- Configure an automatic, nightly logswitch.
- Configure the organization's routine back up software to back up the switched logs every night. Upon evaluation, your plan:
A. Meets the required objective and only one desired objective.
B. Meets the required objective but does not meet either desired objective.
C. Does not meet the required objective.
D. Meets the required objective and both desired objectives.
New Questions 9
What are you required to do before running the command upgrade_export?
A. Run a cpstop on the Security Gateway.
B. Run a cpstop on the Security Management Server.
C. Close all GUI clients.
D. Run cpconfig and set yourself up as a GUI client.
New Questions 10
Fill in the blank with a numeric value. The default port number for standard TCP connections with the LDAP server is
Recommend!! Get the Verified 156-915.80 dumps in VCE and PDF From 2passeasy, Welcome to download: https://arboretumobgyn.com?exam=dumps/156-915.80/ (New Q&As Version)
To know more about the 156-915.80, click here.